How to use the paver patio calculator
- Choose the patio shape and enter its size. For an L-shape or an irregular patio, add up its parts and use Known area.
- Enter the paver size (or tap a common size), the joint width, and a cutting & waste allowance that suits your pattern.
- Check the bedding sand and base depths. They start at ICPI planning values; your site, soil or installer may need more.
- Open Project cost summary to add your prices for pavers, sand and base, plus delivery and tax.
- Download a PDF or print a materials list, or copy a link that reopens your numbers.
How many pavers do I need?
Laying module = (Paver length + Joint) × (Paver width + Joint)
Pavers = Patio area ÷ Laying module
Pavers to buy = Pavers × (1 + Cutting & waste % ÷ 100), rounded up
Including the joint matters: a joint adds a sliver of area around every paver, so wider joints mean fewer pavers per square foot. With 4 × 8 in pavers laid tight, a square foot holds exactly 4.5 pavers; with ¼ in joints it holds about 4.11.
Bedding sand and base: the layers under a patio
Interlocking Concrete Pavement Institute (ICPI) guidance describes a patio as layers on compacted subgrade:
- Compacted aggregate base — at least 4 in (100 mm) after compaction for sidewalks, patios and pedestrian areas over well-drained soil. ICPI guidance calls for bases at least 2–4 in (50–100 mm) thicker on continually wet or weak soils and in colder climates. Driveways need a structural design.
- Bedding sand — coarse, washed sand screeded to a nominal 1 in (25 mm). It is not compacted before the pavers go down, and it must not be used to fill dips in the base.
- Pavers, held by an edge restraint and finished with joint sand.
Loose base material compacts into a thinner layer, so more must be ordered than the finished depth suggests; the extra for compaction & waste setting covers this. Ask your supplier or installer how much to allow for the product you buy.
Joints, patterns and the cutting allowance
The paver count above covers the area exactly; real patios lose pavers to cuts along edges, around obstacles and in patterns. How much depends on the job, so the calculator lets you set it:
- Fewer cuts: rectangular patios in a straight or running-bond pattern, sized to whole pavers where possible.
- More cuts: diagonal and herringbone patterns, curves, circles, borders and many corners.
Joint width depends on the product: many concrete pavers have spacer nibs that set the joint automatically, while natural stone and porcelain are laid with a chosen joint. Use the manufacturer’s laying guide.
Worked examples
A 12 × 10 ft patio in 4 × 8 in pavers laid tight, 5% cutting allowance, 1 in bedding sand, 4 in base, 10% extra on sand and base.
- Area = 12 × 10 = 120 ft²; one paver covers 8 × 4 = 32 in² = 0.2222 ft²
- Pavers = 120 ÷ 0.2222 = 540; with 5% = 567 → 567 pavers
- Bedding sand = 120 × (1 ÷ 12) = 10 ft³; +10% = 11 ft³ = 0.407 yd³ (≈ 0.53 US tons)
- Base = 120 × (4 ÷ 12) = 40 ft³; +10% = 44 ft³ = 1.63 yd³ (≈ 2.61 US tons)
- With illustrative prices of $0.60 per paver, $50/yd³ sand, $40/yd³ base and $75 delivery: $340.20 + $20.37 + $65.19 + $75.00 = $500.76. These are example numbers, not market prices — use your supplier’s.
Metric: a 4 × 3 m patio in 600 × 600 mm slabs with 5 mm joints, 10% cutting allowance, 25 mm bedding sand, 100 mm base, 10% extra.
- Module = 0.605 × 0.605 = 0.366 m²; slabs = 12 ÷ 0.366 = 32.78; +10% → 37 slabs
- Bedding sand = 12 × 0.025 = 0.3 m³; +10% = 0.33 m³ (≈ 0.51 t)
- Base = 12 × 0.1 = 1.2 m³; +10% = 1.32 m³ (≈ 2.51 t)
Assumptions and limitations
- Not a design. Base depth depends on soil, drainage, frost and use. Follow your paver manufacturer’s instructions and local requirements; driveways and problem soils need professional design.
- Not included: edge restraints, joint sand (including polymeric sand — use the product’s coverage figure), geotextile, excavation and disposal, equipment hire and labour.
- Excavation depth is roughly paver thickness + bedding sand + base, plus any allowance your installer specifies for slope and drainage.
- Weights use typical loose densities (97 lb/ft³ for sand and 119 lb/ft³ for crushed base). Your supplier’s figures will differ.
- Prices are only those you enter.
Frequently asked questions
How many pavers per square foot?
Divide 144 by the area of one paver in square inches, including the joint. For 4 × 8 in pavers laid tight that is 144 ÷ 32 = 4.5 per ft²; with ¼ in joints it is 144 ÷ (8.25 × 4.25) ≈ 4.11.
How much sand do I need under pavers?
Bedding sand is screeded to a nominal 1 in (25 mm), so you need about 1 ft³ for every 12 ft² of patio (0.025 m³ per m²), plus a small allowance. The Sand Calculator works it out for any depth.
How thick should the base be under a paver patio?
ICPI guidance gives a minimum of 4 in (100 mm) of compacted base for patios and walkways on well-drained soil, and a thicker base on weak, wet or freezing ground. Follow your manufacturer’s and local requirements.
How much extra should I add for cuts?
It depends on the shape and pattern: straight patterns on rectangles need fewer cuts; diagonal or herringbone patterns, curves and circles need more. Ask your installer or supplier and enter their figure.
Sources & methodology
Unit conversions use exact legal definitions. Material densities are typical planning values that vary in practice — see the calculation methodology for every constant, rounding rule and test.
- ICPI guide specification for interlocking concrete pavement (CCPIC edition, hosted by UC Davis) — Minimum compacted base of 4 in (100 mm) for sidewalks, patios and pedestrian areas; bedding sand screeded to a nominal 1 in (25 mm).
- ICPI Tech Spec 2 — Construction of interlocking concrete pavements (copy hosted by a distributor) — Base thickness depends on traffic, soil, drainage and climate; thicker bases on weak, wet or freezing soils; bedding sand must not be used to correct an uneven base.
- ICPI Tech Spec 17 — Bedding sand selection for interlocking concrete pavements (copy hosted by ORCO) — Bedding sand grading and nominal 1 in (25 mm) layer.
- The Engineering ToolBox — Densities of common materials — General reference values used to sanity-check the sand density range.
- NIST Special Publication 811 — Guide for the Use of the International System of Units (SI) — Exact definitions used for the foot and pound conversion factors.