Gravel & Stone

How to Calculate Gravel for a Garden Path

Measure a garden path in sections, choose a depth, and work out cubic feet, cubic yards and bags of gravel — with a full worked example and sub-base layer.

A narrow gravel path laid along a wooden fence beside a lawn and brick gate pillars
A simple gravel path along a fence line. Straight runs like this are rectangles; widenings at gates are trapezoids. Photo: ghewgill via Flickr · CC BY 2.0 · cropped and resized
On this page (6 sections)

A gravel path is one of the easiest landscaping projects to estimate badly. Paths curve, widen at a gate, and are usually built in layers. The fix is simple: break the path into regular shapes, calculate each layer separately, then add everything up before rounding.

Step 1: Measure the path in straight sections

Walk the path and divide it wherever its width changes or it turns. Each section should be a rectangle (constant width), a trapezoid (a widening section, such as a flare at a gate), a triangle, or part of a circle.

  • For a rectangle, measure length along the centre line and width across.
  • For a trapezoid, measure the two parallel ends and the straight distance between them.
  • For a gentle curve, measure along the centre line and use the average width — the error is small when the curve is gradual.

Step 2: Choose the depth of each layer

Most gravel paths have two layers: a compacted sub-base of angular material that carries the load and drains, and a thinner surface layer that you walk on. Typical planning depths are 2–3 inches (50–75 mm) for the surface layer of a garden path, with a sub-base depth that depends on your ground and how the path will be used. Very deep loose gravel is tiring to walk through, so resist the temptation to go thicker on top.

Cross-section of a gravel path or drivewayA thin top layer of decorative gravel, 2 to 3 inches deep, sits on a compacted sub-base 4 to 8 inches deep, laid on prepared subsoil between edging. 2–3 in (50–75 mm) 4–8 in (100–200 mm) Top layer: decorative gravel Sub-base: crusher run / Type 1, compacted Prepared subsoil (dug out and levelled) Edging Calculate each layer separately — they are different materials with different densities.
Diagram: typical layers of a gravel path or driveway (illustrative, not to scale). Depths are common planning ranges; follow your project specification.

Step 3: Worked example

A path runs 24 ft long and 3 ft wide, then flares into a 5 ft-long section that widens from 3 ft to 6 ft at a patio. It will have 2 inches of pea gravel on top.

SectionAreaVolume at 2 in
Straight run: 24 × 3 ft72 ft²12 ft³
Flare: (3 + 6) ÷ 2 × 5 ft22.5 ft²3.75 ft³
Total94.5 ft²15.75 ft³
  1. Total volume: 15.75 ft³ = 0.583 yd³.
  2. Add 5% for spillage and settling: 15.75 × 1.05 = 16.54 ft³ (0.613 yd³).
  3. In 0.5 cu ft bags: 16.54 ÷ 0.5 = 33.1 → 34 bags. In bulk, round up to 0.75 yd³.

If the straight run also gets a 3-inch sub-base of crusher run, that is a separate calculation: 24 × 3 × 0.25 = 18 ft³ (0.667 yd³) of compacted material. Because crusher run compacts, ask your supplier how much loose material to order for that finished depth.

Step 4: Convert to weight if you’re buying by the ton

Weight = volume × bulk density. Using the typical pea gravel density in our calculator (97 lb/ft³), 16.54 ft³ is about 1,600 lb. Real density varies, so always confirm with your supplier.

Tips for a path that stays put

  • Edge it. Timber, steel, brick or stone edging keeps gravel off lawns and beds.
  • Use angular stone underneath. Rounded pea gravel is pleasant on top but shifts if it is the only layer.
  • Consider a landscape fabric or stabilising grid where weeds or loose ground are a problem.
  • Order once. Adding sections together before rounding avoids paying for several part-loads.

Use the Pea Gravel Calculator for a single section, or the Garden Material Planner to add the straight run, the flare and the sub-base as separate zones and print one materials list.

Sources

  1. NIST Special Publication 811 — Guide for the Use of the International System of Units (SI)
  2. UF/IFAS Gardening Solutions — Walkways in the Landscape — Path width should suit the number of people using it; walkways for more than one person at least 3 feet wide.

Sources were checked when this guide was published. Where published guidance differs, this guide says so; for structural work, follow your local specification.

Worked examples are generated by the same tested calculation engine as our calculators. See our editorial policy and methodology.