Lawn & Grass

How to Calculate Fertilizer: N-P-K Numbers and Pounds per 1,000 sq ft

What the three numbers on a fertilizer bag mean and how to turn a nitrogen rate into pounds of product, bags and metric rates — with a chart and worked example.

Raised vegetable beds and a round brick planter in a community garden, with bark mulch covering the ground between them
Raised beds in a community garden. Fertilizer rates are given per area, so measure the beds or lawn first. Photo: PermaCultured via Flickr · CC BY 2.0 · cropped and resized
On this page (8 sections)

Soil tests and lawn programmes usually give a recommendation in pounds of nitrogen per 1,000 square feet. Fertilizer is sold as a product that is only partly nitrogen. Converting between the two is the most common fertilizer calculation — and the easiest to get wrong.

How much fertilizer your lawn or garden needs depends on the plants, soil, season and region — use a soil test or the product label. Some places restrict fertilizer use or timing; check local rules. This guide is about the arithmetic.

What the three numbers mean

A bag labelled 24-0-6 contains 24% nitrogen (N), 0% phosphate (P₂O₅) and 6% potash (K₂O) by weight. A 15 lb bag therefore holds 15 × 0.24 = 3.6 lb of nitrogen.

From a nutrient rate to pounds of product

Product (lb per 1,000 sq ft) = Nutrient rate ÷ (Nutrient % ÷ 100)
Total product = Product per 1,000 sq ft × Area ÷ 1,000

To apply 1 lb of nitrogen per 1,000 sq ft:

Nitrogen % on baglb of product per 1,000 sq ft
10%10
16%6.25
20%5
24%4.17
29%3.45
32%3.13
46%2.17

Exact: 1 ÷ (% ÷ 100). For a different rate, multiply — for 0.5 lb N, halve the figures.

Worked example

A 6,500 sq ft lawn, a rate of 0.75 lb nitrogen per 1,000 sq ft, using a 29-0-4 product in 15 lb bags.

  1. Nitrogen needed: 6.5 × 0.75 = 4.875 lb
  2. Product: 4.875 ÷ 0.29 = 16.8 lb (2.59 lb per 1,000 sq ft)
  3. Bags: 1.12 → 2 bags

The rate is only an example for the arithmetic.

Checking a bag’s coverage claim

Many bags say something like “covers 5,000 sq ft”. You can turn that into the nitrogen rate it delivers, and compare it with the rate you want:

Product per 1,000 sq ft = Bag weight ÷ Coverage × 1,000
Nitrogen per 1,000 sq ft = Product per 1,000 sq ft × (N % ÷ 100)

For example, a 15 lb bag of 29-0-4 that covers 5,000 sq ft applies 15 ÷ 5,000 × 1,000 = 3 lb of product per 1,000 sq ft, which is 3 × 0.29 = 0.87 lb of nitrogen per 1,000 sq ft. If that is more than your soil test or programme calls for, spread the bag over a larger area or use a lower spreader setting.

Phosphate and potash

The same formula works for the second and third numbers. If a soil test recommends 0.5 lb of potash (K₂O) per 1,000 sq ft and your product is 0-0-50, you need 0.5 ÷ 0.50 = 1 lb of product per 1,000 sq ft. With a blended product, the rate that satisfies one nutrient fixes the amount of the others — check that none of them is applied where it is not needed.

Metric rates

  • 1 lb per 1,000 sq ft = 4.882 g per m² = 0.4882 kg per 100 m²
  • Product (g per m²) = nutrient (g per m²) ÷ (nutrient % ÷ 100)

Spreading evenly

  • Set your spreader to the product’s label setting and check it on a measured area.
  • Apply half the product in one direction and half at right angles to avoid stripes.
  • Sweep granules off paths and drives back onto the lawn.

The Fertilizer Calculator does the conversion in imperial or metric units and counts the bags. Measure the lawn first with the Square Footage Calculator.

Sources

  1. NIST Special Publication 811 — Guide for the Use of the International System of Units (SI) — Exact definitions of the inch, foot, yard, acre, pound, US gallon and the cubic yard used in every calculation in this guide.

Sources were checked when this guide was published. Where published guidance differs, this guide says so; for structural work, follow your local specification.

Worked examples are generated by the same tested calculation engine as our calculators. See our editorial policy and methodology.