Soil & Garden Beds

How Much Mulch Do I Need for My Garden?

How deep to spread mulch, how to measure beds and tree rings, and how to turn square feet into bags or cubic yards — with worked examples and a top-up method.

Raised vegetable beds and a round brick planter in a community garden, with bark mulch covering the ground between them
Beds and planters in a community garden, with bark mulch covering the ground between them. Photo: PermaCultured via Flickr · CC BY 2.0 · cropped and resized
On this page (8 sections)

Mulch is sold by volume — bags labelled in cubic feet or litres, or bulk by the cubic yard or cubic metre — so the question “how much do I need?” comes down to two numbers: the area of your beds and the depth you want. Here is how to get both right, and how to avoid the two most common mistakes: spreading it too deep and buying for the full depth when you are only topping up.

Cubic feet = Area (ft²) × Depth (in) ÷ 12
Cubic yards = Area (ft²) × Depth (in) ÷ 324
Bags = Cubic feet ÷ bag size, rounded up

How deep should mulch be?

University extension services broadly agree on a layer about 2 to 4 inches deep. The University of Illinois Extension suggests the shallower end for fine, composted materials and the deeper end for coarse mulches such as wood chips. Deeper is not better: a very thick layer can keep water from reaching the soil.

UseTypical depth (inches)Typical depth (mm)
Shrub and flower beds2–3 in50–75 mm
Ring around a tree (kept off the trunk)2–4 in50–100 mm
Woodland / bark paths3–4 in75–100 mm

Keep mulch pulled back from tree trunks and plant stems. Recommended gaps vary between sources — several inches is common advice — but every source warns against “volcano mulching”, piling mulch up against the trunk, which keeps bark wet and encourages roots to grow into the mulch.

Measure your beds

  • Rectangular beds: length × width.
  • Tree rings: π × (diameter ÷ 2)². The University of Tennessee suggests a mulch ring at least 4 to 6 feet across for trees.
  • Curved borders: measure the length along the middle of the border and the width in several places, then multiply the length by the average width.
  • Odd shapes: split them into rectangles, triangles and circles, and add the areas together.

Leave out areas that will not be mulched, such as large shrubs’ root crowns or a path running through the bed.

Worked examples

A 20 ft × 5 ft border, 3 inches deep, in 2 cu ft bags.

  1. Area = 20 × 5 = 100 ft².
  2. Volume = 100 × 3 ÷ 12 = 25 ft³ = 0.926 yd³.
  3. Bags = 25 ÷ 2 = 12.5 → 13 bags.

A tree ring 6 ft across, 3 inches deep.

  1. Area = π × 3² = 28.3 ft².
  2. Volume = 28.27 × 3 ÷ 12 = 7.07 ft³ → 4 bags of 2 cu ft (keep the mulch off the trunk itself).

Metric: a 6 m × 1.5 m border, 7.5 cm deep, in 60 L bags.

  1. Volume = 6 × 1.5 × 0.075 = 0.675 m³ = 675 litres.
  2. Bags = 675 ÷ 60 = 11.25 → 12 bags.

Topping up existing mulch

Most beds already have some mulch from last year. Push a ruler down in a few places, take the average, and subtract it from your target depth.

Topping up mulchA bed already has 1 inch of old mulch. To reach a 3 inch target, only 2 inches of new mulch are needed. Add 2 in Existing 1 in Target 3 in New mulch to buy Old mulch already in the bed Soil Depth to add = target depth − existing depth
Diagram: when topping up, buy only the difference between your target depth and the mulch already there (illustrative, not to scale).

For the 20 × 5 ft border above, with 1 inch of old mulch and a 3-inch target, you only need 2 inches: 16.7 ft³, or 9 bags instead of 13. The Mulch Calculator has a field for the depth already there and does this subtraction for you.

Bags or bulk?

A cubic yard is 27 cubic feet, so it equals 13.5 bags of 2 cu ft or 9 bags of 3 cu ft. A cubic metre is 1,000 litres — 20 bags of 50 L. Coverage at common depths:

Coverage of one cubic yard at different depthsOne cubic yard covers 324 square feet at 1 inch deep, 162 at 2 inches, 108 at 3 inches and 81 at 4 inches. Area covered by 1 cubic yard (27 ft³) of loose material 1 in deep 324 ft²2 in deep 162 ft²3 in deep 108 ft²4 in deep 81 ft² Rule of thumb: coverage in ft² = 324 ÷ depth in inches.
Diagram: the deeper the layer, the less area each cubic yard covers. Exact for a level surface.

Bulk mulch is usually sold by the cubic yard or cubic metre and delivered, so compare the delivered price with the bag price for your quantity. Our guide to landscaping material costs shows how to compare the two fairly.

Should you buy extra?

Mulch settles as it is raked out and watered in, and some always ends up on paths. A small allowance is reasonable. With 10% extra, the 20 × 5 ft border needs 27.5 ft³ — 14 bags, or 1.25 yd³ in bulk rounded up to the nearest quarter yard. Add the margin once; see how to calculate material waste.

Common mulch mistakes

  • Too deep: more than about 4 inches can restrict water and air reaching the soil.
  • Against trunks and stems: leave a gap; never build a volcano.
  • Buying for the full depth when topping up: measure the old layer first.
  • Mixing up bag units: US bags are labelled in cubic feet, UK and Australian bags in litres.

Sources

  1. University of Illinois Extension — Proper mulching techniques (infosheet) — A 2–4 inch layer; finer composted mulch at the shallow end, coarse mulch at the deeper end; keep mulch away from trunks.
  2. Penn State Extension — Learning how to properly mulch can save your tree
  3. University of Maryland Extension — Excess mulch problems
  4. University of Tennessee — SP617 Mulching your trees and landscapes
  5. Iowa State University Extension — How to determine the amount of mulch needed for a garden bed

Sources were checked when this guide was published. Where published guidance differs, this guide says so; for structural work, follow your local specification.

Worked examples are generated by the same tested calculation engine as our calculators. See our editorial policy and methodology.