
On this page (9 sections)
A gravel driveway is a stack of layers, not a single pour of stone. To order the right amount you need the area of the driveway, the depth of each layer, and the material for each layer. This guide works through all three, then converts the result to the tons your supplier may quote.
Cubic metres = Length (m) × Width (m) × Depth (m)
Weight = Volume × Density (ask your supplier for the density of their product)
Start with the layers
Most gravel driveways have at least two layers:
- Sub-base — a well-graded crushed stone with fines, sold as crusher run, dense-graded aggregate, road base or (in the UK) Type 1. The mix of sizes locks together when compacted and carries the load.
- Surface layer — a cleaner, angular stone such as No. 57 crushed stone (a standard size designation in ASTM D448, roughly 1 inch down to about 3/16 inch). Angular stone interlocks; rounded pea gravel tends to roll and rut under tires, which is why it is better kept for paths.
Some builds add a coarser bottom layer on soft ground, or a woven geotextile under the stone to stop it sinking into clay. Each extra layer is one more line on your order.
How deep should each layer be?
There is no single national standard for a residential gravel driveway. The Federal Highway Administration’s gravel roads guide is explicit that it is not a specification, and published home-improvement guidance ranges from about 6 inches of compacted stone in total to 12 inches or more. Deeper builds are used for heavy vehicles, soft or wet subsoil, and cold climates.
These are the planning ranges our calculators use:
| Use | Typical depth (inches) | Typical depth (mm) |
|---|---|---|
| Decorative beds | 2–3 in | 50–75 mm |
| Garden path (top layer) | 2–3 in | 50–75 mm |
| Gravel patio / seating area | 3–4 in | 75–100 mm |
| Driveway top layer | 2–4 in | 50–100 mm |
| Driveway sub-base (compacted) | 4–8 in | 100–200 mm |
If your ground is soft clay, holds water, or the driveway will take delivery trucks or an RV, get local advice before deciding — a contractor who knows your soil will specify the sub-base depth. The calculation itself does not change: you simply use their depths.
Measure the driveway in simple shapes
Driveways are rarely one perfect rectangle. Split yours into pieces you can measure:
- Straight runs are rectangles: length × width.
- A flared apron where the driveway meets the road is a trapezoid: (width at the house end + width at the road) ÷ 2 × the distance between them.
- A turning circle is a circle: π × (diameter ÷ 2)².
Measure in feet (or metres), and measure the finished surface you want, not the hole you will dig. Calculate each piece and add them together before rounding.
Worked example: a 50 ft driveway with a flared apron
A driveway runs 50 ft long and 12 ft wide, then flares from 12 ft to 18 ft over the last 8 ft at the road. It will have a 6-inch sub-base of crusher run and a 3-inch surface of crushed stone.
| Section | Area | Sub-base (6 in) | Surface (3 in) |
|---|---|---|---|
| Straight run 50 × 12 ft | 600 ft² | 11.11 yd³ | 5.56 yd³ |
| Apron (12 + 18) ÷ 2 × 8 ft | 120 ft² | 2.22 yd³ | 1.11 yd³ |
| Total | 720 ft² | 13.33 yd³ | 6.67 yd³ |
- Sub-base: 720 ft² × 6 ÷ 324 = 13.33 yd³ before any allowance for compaction.
- Surface: 720 ft² × 3 ÷ 324 = 6.67 yd³.
- Weight at typical densities: sub-base about 21.4 US tons (range 19.1–23.6); surface about 9 US tons (range 8.1–9.8).
Metric version: a 15 m × 3.5 m driveway with 150 mm of sub-base and 75 mm of surface stone needs 7.88 m³ of sub-base (about 15 tonnes) and 3.94 m³ of surface stone (about 6.3 tonnes), before allowances.
Allow for compaction — but get the figure from your supplier
Crusher run and other graded bases shrink when they are rolled or plate-compacted, so a 6-inch compacted layer needs more than 6 inches of loose stone. How much more depends on the product, its moisture and the equipment, so ask the supplier how much loose material they recommend for your finished depth, and enter that as the extra allowance in the calculator.
For example, if a supplier advised adding 15% to the sub-base (an illustrative figure only), the order in our worked example would rise from 13.33 to 15.33 yd³. Clean surface stone compacts much less.
Cubic yards or tons?
Many quarries sell by weight. To convert, you need the bulk density of the exact product, which varies with rock type, grading and moisture. Typical ranges:
| Material | Typical range (lb/ft³) | US tons per yd³ | Tonnes per m³ |
|---|---|---|---|
| Crusher run / Type 1 sub-base (loose) | 106–131 | 1.43–1.77 | 1.7–2.1 |
| Crushed stone (e.g. #57 / 20 mm clean) | 91–109 | 1.22–1.47 | 1.45–1.75 |
| Gravel (general, loose) | 91–109 | 1.22–1.47 | 1.45–1.75 |
Typical values for loose, as-delivered material. They are planning approximations, not specifications — your supplier’s figure for their product always takes priority.
On these figures, one cubic yard of crusher run weighs roughly 1.43–1.77 US tons. The Gravel Calculator shows the weight as a range and accepts your supplier’s density for a tighter figure. If you are comparing quotes in different units, see how to calculate landscaping material costs.
Shape the surface so water runs off
Water is the main cause of potholes and soft spots in gravel. Guidance for gravel roads recommends a crown — a gentle slope from the centre to each edge — of about 4%. On a 12 ft driveway that is a fall of roughly 2.9 inches from the centre line to each edge. Build the crown into the sub-base, not just the top layer, and make sure water leaving the edges has somewhere to go.
Before you order
- List each layer separately with its material, finished depth and volume.
- Ask the supplier for density (if they sell by weight) and for their compaction advice on the base.
- Check minimum loads and delivery access: a full truck needs firm ground and room to tip.
- Round up once, per material, after adding all sections together.
- Plan where the stone will be tipped so it does not block the work.
Enter each layer in the Gravel Calculator, or add the straight run, apron and each layer as separate zones in the Garden Material Planner to get one combined, printable order list.
Sources
- FHWA — Gravel Roads Construction & Maintenance Guide (2015) — Shaping, crown and drainage of gravel surfaces. Not a national specification.
- Kansas LTAP fact sheet — Gravel roads — Recommends about a 4% cross-slope (crown) on gravel surfaces so water runs off.
- ASTM D448 — Standard Classification for Sizes of Aggregate for Road and Bridge Construction — Defines size numbers such as No. 57 and No. 8.
- Angi — How to make a gravel driveway — Industry example of layered construction and total depth.
- Stone Centers — How to make a gravel driveway — Industry example of a three-layer build.
Sources were checked when this guide was published. Where published guidance differs, this guide says so; for structural work, follow your local specification.
Worked examples are generated by the same tested calculation engine as our calculators. See our editorial policy and methodology.


