
On this page (10 sections)
Plant labels say something like “space 12 inches apart”. Turning that into the number of pots to buy for a bed is simple geometry — and the pattern you plant in changes the answer by about 15%.
What “on center” means
Spacing is measured from the centre of one plant to the centre of the next. It reflects how wide the plant grows; closer spacing fills in sooner but costs more and may need thinning later.
Square grid
Each plant sits at the corner of a square, so it “owns” spacing × spacing of ground. At 12 in (1 ft), each plant occupies 1 sq ft.
Staggered (triangular) grid
Offset every other row by half a spacing and every plant is the same distance from six neighbours. Each one occupies spacing² × √3 ÷ 2 ≈ 0.866 × spacing², so you fit about 15% more plants and cover fills in evenly with no straight gaps — the usual choice for ground covers and mass plantings.
Plants per 100 square feet
| Spacing | Square grid | Staggered grid |
|---|---|---|
| 6 in | 400 | 461.9 |
| 9 in | 177.8 | 205.3 |
| 12 in | 100 | 115.5 |
| 15 in | 64 | 73.9 |
| 18 in | 44.4 | 51.3 |
| 24 in | 25 | 28.9 |
| 30 in | 16 | 18.5 |
| 36 in | 11.1 | 12.8 |
Exact results of the two formulas for 100 sq ft. Scale for your area and round up.
Worked example
A 60 sq ft bed of ground cover at 12 in spacing.
- Staggered: 60 ÷ (1 × 1 × 0.866) = 69.3 → 70 plants
- Square grid: 60 ÷ 1 = 60 plants
Counting by rows instead
For a rectangular bed you can also count plants row by row, which is how you will lay them out on the ground:
Round each to whole plants. A 10 × 4 ft bed at 12 in spacing gives 10 plants per row in 4 rows — 40 plants. In a staggered layout the rows are only 0.866 × spacing apart, so the same bed fits more rows; alternate rows are shifted half a spacing and may hold one plant fewer.
Choosing a spacing
- Follow the label. It is based on the plant’s mature width, which is the best guide to how far apart they should end up.
- Closer for faster cover: planting at the closer end of a range fills the bed sooner and shades out weeds, but costs more plants.
- Wider for air and access: plants prone to leaf diseases, and beds you need to walk into, benefit from the wider end.
Buying in flats and trays
Ground covers and bedding plants are often sold in flats or plug trays. Divide the number of plants by the number in one flat and round up: 116 plants from flats of 18 is 116 ÷ 18 = 6.4 → 7 flats.
Edges and odd shapes
- Plants along a path or lawn edge are usually set about half a spacing in from the edge, which slightly reduces the count for narrow beds.
- For curved or irregular beds, find the area first with the Square Footage Calculator.
- Mixed plantings: work out each group’s area and spacing separately and add them.
The Plant Spacing Calculator does the arithmetic for both patterns. Then plan the mulch to cover the bed between plants.
Sources
- NIST Special Publication 811 — Guide for the Use of the International System of Units (SI) — Exact definitions of the inch, foot, yard, acre, pound, US gallon and the cubic yard used in every calculation in this guide.
Sources were checked when this guide was published. Where published guidance differs, this guide says so; for structural work, follow your local specification.
Worked examples are generated by the same tested calculation engine as our calculators. See our editorial policy and methodology.

